Mounting A Tub
Mounting A Tub
Blog Article
We have noticed the article on How to Install a Bathtub Yourself listed below on the net and decided it made good sense to discuss it with you on this page.
Installing a tub isn't specifically brain surgery, but it does require strong plumbing, woodworking, as well as occasionally, tiling abilities. Replacing an old bath tub with a new one is also a reasonably hard project. If the old bathtub is conveniently available, the task can move rapidly; if you need to open a wall to get rid of the old bathtub and place the brand-new bathtub, the task is a lot harder. In either case, the project is within a house handyman's abilities, although you will certainly require an assistant to move out the old tub as well as embeded in the new one. Make certain you have certified on your own for the job and also fit attempting it. Instead of hiring a professional to take control of a halfway-completed project, it is far better to consider utilizing one prior to you begin. Opportunities are you might need a specialist plumber to make tube connections.
This post will certainly assist you mount a new tub in your washroom if you have already acquired a new bathtub and don't require to transform the plan of your previous water supply pipes.
Your devices as well as product list ought to consist of the following:
Getting ready for the Installment
Firstly, the supporting structure supplied with the bathroom should be fitted (if needed) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is important to ensure that if the faucet includes a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the taps system to prevent pressure on the bath tub.
Fit the flexible faucet adapters to the bottom of the two taps making use of 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you use all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath should now prepare to be suited its last placement.
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your setup, then the first thing you ought to do is detach the water system. After doing so, turn on the taps to drain pipes any kind of water continuing to be in the system. The process of eliminating the existing taps can be fairly troublesome because of the restricted accessibility that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a towel prepared for the remaining water that will originate from the pipes. When the supply pipelines have been gotten rid of, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from transforming throughout this procedure. Once the taps have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any type of old securing substance.
Before carrying on to fit the brand-new faucets, compare the pipe links on the old faucets to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Mounting the Bathtub
Using the two wooden boards under its feet, put the bath tub in the required position. The wooden boards are practical in equally spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 tiny factors.
The next goal is to guarantee that the tub is leveled all round. This can be accomplished by checking the spirit level and also changing the feet on the bath tub till the spirit level reads level.
To install faucets, fit all-time low of the outermost adaptable tap connector to the suitable supply pipe by making a compression join; after that do the same for the other tap.
Switch on the water supply and check all joints as well as new pipework for leaks as well as tighten them if required. Fill the bathtub and also check the overflow outlet and the normal outlet for leaks.
Ultimately, deal with the bathroom paneling as defined in the maker's instruction manual. Tiling as well as sealing around the bathtub needs to wait up until the tub has been used a minimum of once as this will settle it right into its last setting.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic connector to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end provides a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly require reducing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, position the faucet in the installing opening in the bath/basin making sure that the washers are in area in between the tap and the sink. Safeguard the faucet in place with the manufacturer supplied backnut. Once the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap adapters. The former kind ought to be attached to the tap finishes first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the area where the bath meets the floor tile, it is required to secure the joins with a silicone rubber caulking. This is important as the fitting can relocate sufficient to crack a stiff seal, causing the water to permeate the wall surface between the bathroom and the tiling, bring about problems with wetness and feasible leakages to the ceiling below.
You can pick from a variety of coloured sealants to assimilate your fixtures as well as installations. They are marketed in tubes and cartridges, as well as can securing gaps up to a width of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly fill the bath tub with water prior to securing, to allow for the movement experienced when the tub is in use. The sealant can split relatively very early if you do not take into account this activity before securing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally conveniently readily available on the marketplace. It is a good idea to fit the tiles using waterproof or water-proof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a person who reads on How to Install a Bathtub Yourself, I thought sharing that piece of writing was sensible. Enjoyed reading our entry? Please share it. Let somebody else discover it. I take joy in reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Request An Estimate
Report this page